Skip to content

8 min read · Published 17 Nov 2026

Used Whatsminer Buying Guide: What to Check Before You Pay in Dubai

Checked against MicroBT’s published product pages and documents: 17 November 2026.

Used Whatsminer Buying Guide: What to Check Before You Pay in Dubai

A used Whatsminer is worth buying when six things check out: the serial matches the machine and the manufacturer’s records, it boots without serious error codes, it hashes at the bin on its label, it draws the power MicroBT’s efficiency figure says it should, its hashboards have an honest history, and it runs MicroBT’s own firmware. None of these needs special tools beyond a laptop and a plug-in power meter, and a seller who refuses any of them has told you something.

This guide takes each check in turn, using only what MicroBT itself publishes. It is written for buyers in Dubai and the wider UAE, where most used units on offer are earlier air-cooled models and where heat is part of every machine’s history.

Which used Whatsminer models you will be offered

MicroBT’s own shop marks several earlier models, including the M30S+, M30S++ and M50S, as sold out, so units of those models on the UAE market today are almost always second hand MicroBT shop listing, 9 November 2026. The M60 family is the current air-cooled line on the same listing, and used M60 and M60S units are starting to appear.

Model Hashrate bins MicroBT lists Printed power on wall Printed efficiency Published operating range
M30S+ 100 TH/s 3,400 W 34 J/TH -5 to 35 C
M50S+ 152 to 156 TH/s (three bins) 3,344 to 3,432 W 22 J/TH -5 to 35 C
M50S++ 160 to 162 TH/s (two bins) 3,360 to 3,402 W 21 J/TH -5 to 35 C
M60 168 to 174 TH/s (three bins) 3,343.2 to 3,462.6 W 19.9 J/TH -5 to 35 C
M60S 184 to 188 TH/s (three bins) 3,404 to 3,478 W 18.5 J/TH -5 to 35 C

MicroBT M30S+ MicroBT M50S+ MicroBT M50S++ MicroBT M60 MicroBT M60S

MicroBT lists a power figure for each bin, shown when you select the bin on its listing; the ranges above cover the listed bins. Use the bin printed on the machine’s own label, and MicroBT’s figures for that bin, as your reference. The current range and what each model needs is on our Whatsminer in Dubai page.

Check 1: the serial, the label and the warranty

Start with the label on the chassis. The model, the bin and the serial number on that label should match three other things: the model and bin the seller quoted, the serial the machine reports in its own web interface or in WhatsMinerTool, and any invoice the seller shows you. A mismatch between the label and the dashboard is the first sign of a relabelled unit or a swapped control board.

Then the warranty. MicroBT’s product pages offer “a one-year warranty period and repair services within the warranty scope” MicroBT M60S after-sales policy. The same policy excludes products whose serial numbers have been “maliciously modified, defaced, or intentionally removed”, unauthorised disassembly or repair, and unofficial accessories such as power supplies, control boards, fans and cables. So a unit with a tampered serial, or with parts that are not MicroBT’s, is outside MicroBT’s warranty on MicroBT’s own terms, whatever its age.

MicroBT’s support centre has a Warranty Check that asks for the machine’s serial number (SN) WhatsMiner Support Center. So photograph the label before you agree a price, and ask the seller for the original purchase date. For Antminer units, our guide to checking a warranty by serial number walks through Bitmain’s lookup.

Check 2: error codes on boot

Power the machine on in front of you, let it start hashing, and read the status in WhatsMinerTool or the web interface. MicroBT publishes the meaning of every code in its “WhatsMinerTool Error Code Description”, and our Whatsminer error codes guide groups them by family.

On a used unit, a few codes deserve a direct question before you pay:

  • 51X and 52X. A hashboard type or chip bin type that does not match the rest of the machine. This is what mixed boards look like.
  • 53X. The hashboard on slot X was not found. The machine is running on fewer boards than it should.
  • 55X, 57X, 59X. Bad chips, chip transfer errors or frequency too low. MicroBT’s suggested action is to contact its after-sales service.
  • 8400 and 8410. Wrong or unofficial firmware.
  • 901. A power rate error, where MicroBT’s suggested action is to check whether the miner has been modified.
  • 600 and the heat family. Ambient above 35 C in normal mode. On a used machine this tells you about the room it has been running in.

A clean boot is not proof of a healthy machine. It is the minimum before you go further.

Check 3: hashrate against the bin

The bin on the label is what the machine should deliver. Ten minutes on a dashboard shows very little, because hashrate reported over a short window moves a lot. Ask for the machine to run on a pool for as long as you can arrange, ideally a full day, and compare the pool-side average hashrate with the label bin. A result well below the bin on a machine that reports no errors usually points to a weak board or throttling from heat.

Keep in mind that MicroBT lists bins as separate products. An M60S sold as 188 TH/s should be compared with 188, not with the lower bins on the same page.

Check 4: wall power against MicroBT’s efficiency figure

This is the check that exposes a relabelled bin. Plug the machine into a power meter rated for a continuous load of this size, let it settle, and read the watts. Then divide the measured watts by the hashrate the pool reports.

The check
Measured efficiency (J/TH) = measured watts ÷ reported hashrate (TH/s)

Compare that with MicroBT’s printed efficiency for the model: 18.5 J/TH for an M60S, 21 J/TH for an M50S++, 22 J/TH for an M50S+ MicroBT shop listing. A small difference is normal for a used unit. A machine drawing far more power than its printed efficiency allows for the hashrate it delivers is either worn, misconfigured or not the bin it claims to be.

While it runs, check the supply side too. MicroBT specifies the P221B or P222B PSU on AC 220 to 240 V for the M60 and M50S families, with a C19 lead rated 16 A or more. A different PSU model is an “unofficial accessory” under MicroBT’s own exclusions.

Check 5: hashboard history

Ask the seller directly: has any board been repaired, replaced or moved from another machine? An honest seller of a two- or three-year-old unit will often say yes. That is not a reason to walk away on its own. What matters is that the answer matches what you see:

  • the board count and the error log (Check 2);
  • the hashrate against the bin (Check 3);
  • the condition inside the case, if the seller will open it on a video call.

Remember MicroBT’s exclusions: unauthorised disassembly and repair void its warranty. A unit that has been opened and repaired outside MicroBT’s channel is an out-of-warranty unit, and should be priced as one. For what a board fault looks like and what repair involves, see our guide to spotting a fake or tampered Whatsminer, which covers the open-case signs.

Check 6: firmware

A used Whatsminer should be on MicroBT’s own firmware. MicroBT’s warranty excludes problems caused by “unofficial software” and by self-modified parameters such as overclocking MicroBT M60S after-sales policy. Codes 8400 and 8410 in MicroBT’s error table flag wrong or unofficial firmware directly.

Check the firmware version in WhatsMinerTool and compare it with the releases on MicroBT’s firmware download page MicroBT firmware download. MicroBT’s WhatsMinerTool guide notes that some functions only support firmware versions after 20241011.12, so a very old version is worth a question too MicroBT, WhatsMinerTool guide, 29 October 2025.

The heat question for a used Whatsminer in the UAE

Every air-cooled Whatsminer in the table above carries the same published operating range: -5 to 35 C. A machine that spent summers in an unconditioned room or container in the UAE ran outside that range for long stretches. Ask where it ran, and whether the room was cooled. Heat history does not show on a label, but it often shows in the error log, in fan speeds and in hashrate below the bin.

Buying used in Dubai

A buyer in Dubai has one advantage over an online buyer: you can see the machine run before you pay. Use it. Ask for the serial photos and the model and bin in writing first, then arrange to watch the six checks on the machine itself.

If you would rather start from units that have already been through a bench, our used Whatsminer for sale in Dubai page lists what we can supply. Used units we sell are bench-tested before sale.

Frequently asked questions

Is a used Whatsminer worth buying?

It can be, if the six checks pass and the price reflects the machine's age and efficiency. Older models such as the M30S+ draw 34 J/TH on MicroBT's figures, against 18.5 J/TH for the M60S, so run the power cost at your own tariff before you compare prices.

Does a used Whatsminer still have MicroBT's warranty?

MicroBT's product pages offer a one-year warranty and exclude tampered serials, unauthorised repair and unofficial parts. Whether a resold unit is still covered depends on its original purchase date and its condition. Ask for the original invoice, and check the serial with MicroBT before you rely on it.

What error codes should stop me buying?

Ask hard questions about 51X or 52X (mismatched boards), 53X (a missing board), 55X, 57X or 59X (chip faults), 8400 or 8410 (unofficial firmware) and 901 (possible modification). None of them is an automatic no, but each needs an answer before money changes hands.

How do I know the hashrate is real?

Run it on a pool for as long as possible and compare the pool-side average with the bin on the label. Then measure wall power and divide by that hashrate. The result should sit close to MicroBT's printed J/TH for the model.

Can I check a used Whatsminer I have already bought?

Yes. Send the model, serial and a WhatsMinerTool screenshot on WhatsApp, or bring it to our Deira workshop for a diagnosis before any work is quoted.

Tell us the models and quantity

Send a message on WhatsApp with the models and quantity you want, and you'll get a live price and the collection or delivery options for your city.